Skip to content
All extraction guides

Extraction Equipment Planning for Biobanks and CROs

Group compatible projects, preserve sample-to-eluate records and plan repeat capacity before comparing automated purification systems.

Published
Reading time
4 min read
Author
Nucleic Acid Extractors

Biobanks and contract research organizations should size extraction equipment around compatible project batches and the sample-to-eluate handoff. A large daily specimen count does not show how many samples can share one method, run or release schedule.

The purchasing brief should connect sample preparation, purification, identity records and downstream release. The distinctive task is to keep those project requirements together while comparing equipment capacity.

Group projects by method before combining their counts

List the preparation and extraction requirements for each project. Only then decide which work can share a proposed run.

Project fieldWhy it matters to the equipment decision
Specimen type and received conditionDefines which preparation and method documentation apply
Target and downstream useDefines the output and assessment requirements
Kit/IFU and program revisionDistinguishes methods that may need separate runs
Routine batch and release timingShows whether a large run or several smaller batches fit the work
Controls, repeats and reserve materialChanges available capacity and remaining sample requirements

The NCI biospecimen best-practices overview explains why processing, storage and associated data can affect the usefulness of research biospecimens. Use the laboratory’s approved procedures to define these project fields; an equipment article cannot set one handling method for every repository.

Define the sample-to-eluate record

Before reviewing software features, agree on the record that must survive each manual or automated handoff. A simple example contains:

  1. Incoming sample identifier and project.
  2. Prepared aliquot or fraction identifier.
  3. Extraction run, method/program revision and position.
  4. Output vessel or plate position.
  5. QC disposition and destination of the remaining material.

This is an example of information to specify, not a claim that an instrument captures it automatically. Ask which records the proposed configuration creates, which require an operator and how the laboratory will verify transfers.

Keep LIMS integration, barcode handling and electronic record requirements as separate questions. A USB or network port is not evidence that a particular integration, audit trail or sample-management workflow is supported.

Reserve positions and material for the full job

Allocate the controls and planned repeats required by each method before counting available specimen positions. Also consider the material reserved for QC and any later project work.

If projects use different preparation or output requirements, a high maximum capacity may still leave separate scheduling constraints. Compare the size of the compatible batch, the preparation work and the release deadline together.

The 96-well workflow guide covers plate allocation and output handoff. The NGS selection guide adds sequencing-library input requirements where relevant. This guide focuses on the project and identity record around those workflows.

Compare equipment after the method groups are clear

MultiEX 016, 032 and 096P list manufacturer-stated capacities of 1–16, 1–32 and 1–96 samples per run, respectively. MultiEX 024L is a separate 1–24-sample large-volume tier. Batch size and processing volume must be considered independently.

Use the model comparison to shortlist equipment. Then request the exact kit, program, plastics and output combination for each intended method group. A common instrument family does not make all project methods interchangeable.

Ask the purchasing channel to distinguish equipment supply from any other requested service. This website facilitates equipment inquiries; it does not offer contract extraction, biobanking, hands-on validation or LIMS integration services.

Send a project-aware equipment brief

Summarize representative method groups, routine batch sizes, control allocation, release timing, working volumes and required output records. Include the equipment and documentation questions that need to be resolved before a purchase decision.

For larger compatible batches, send a MultiEX 096P purchase inquiry. If the workload is split across smaller methods, include that detail so another tier can be considered. Technical fields are optional at first contact.

Biobank and CRO equipment questions

Should all projects be combined to justify one larger extractor?

No. Identify which preparation and program requirements can be shared, then compare the resulting compatible batches and schedules.

Does a connectivity port establish LIMS integration?

No. Request the actual supported functions and documentation, then assess them against the laboratory’s record and integration requirements.

Planning an extraction workflow?

Share your sample type, routine batch size and kit requirements with Surge Scientific.

Discuss your workflow